トレーニングウエポン(トレポン)＆周辺パーツ関連情報

ACOG 6X48 TA648MGO
TA648MGO: 6x48 Trijicon ACOG with Red Chevron Reticle and Accessory M1913 Rail


The military’s need for a magnified, self-luminous tactical sight that enhances target identification and increases hit
probability on extended-range shots has given rise to the new Trijicon ACOG® 6x48. Powered by Trijicon’s patented
fiber optics and tritium-based technology, the new TA648MGO ACOG reticle features a red chevron aiming point.
It also incorporates a bullet drop compensator (BDC) with additional aiming points estimated for trajectory of the 5.56mm
855 out to 800 meters. To further improve target acquisition and hit potential, the new ACOG® 6x48 incorporates
Trijicon’s Bindon Aiming Concept™ (BAC) – a revolutionary both-eyes-open method of aiming. Like other members
of the Trijicon ACOG® line, the new ACOG® 6x48 is battery free and waterproof to 328 feet. This model of the 6x48
ACOG features an M1913 Military rail for mounting of additional Trijicon products such as the RedDot and Reflex.

ＴＲＩＪＩＣＯＮ製　ACOG 6X48 TA648MGO

TA31系と較べるとかなり巨大です。
倍率が6ｘなのでMINIMIやM27等に似合うと思います。

在庫/価格のお問合せ/お求めはモデルショップPAPAまで
メール　hirokomama0527@yahoo.co.jp

モデルショップPAPA　http://modelshoppapa.shop-pro.jp/　
こちらでもお求め可能です。
  

PRI Free Float Forearm System - Mid Length


GenIII AR15/M16 Free Float Forearm System Intermediate - The latest Pri Gen III Freefloat Forearm and barrel nut
are constructed of light weight high strength carbon fiber aluminum and high strength steel for the best possible
combination of weight and strength. The carbon fiber also reduces the amount of heat transferred to the shooter's
hand during rapid or high volume firing. The long top rail matches the height of the top rail on the standard flattop
receiver and is compatiable with the ARMS family of rails. The most rigid M16 freefloat system available is now
easier to install. SPR* is a registered trademark of Armalite Inc. and is used under license agreement.

ＰＲＩ製カーボン　フリーフロート　フォアアーム　MIDレングス

米国ＰＲＩ社製のカーボンレールです。
画像は.223用ミドル長ですが.223のライフル長や.308用もあります。
お探しの機種があれば下記まで連絡下さい。

在庫/価格のお問合せ/お求めはモデルショップPAPAまで
メール　hirokomama0527@yahoo.co.jp

モデルショップPAPA　http://modelshoppapa.shop-pro.jp/　
こちらでもお求め可能です。

  

JP AR Tension Pin for Standard Rifle


Finally, the right fix for the “loose” upper/lower receiver problem. You can throw out that piece of rubber you’ve
been stuffing under your rear take-down pin all these years. All it’s good for is eliminating the “rattle” in your gun.
In reality, it does just the opposite of what it should. It pushes the receiver halves apart on a flexible interface.
They still move when the gun discharges. The JP Precision Tensioning Pin actually pulls the whole upper assembly
down and back on the lower with reproducible torque (for those really picky folks) and gives a rock hard fit to even
the sloppiest receivers. Ask any bolt gun shooter, and they will tell you that a rifle loose in the stock will most likely
not reach its accuracy potential. An AR with a loose upper/lower is no different. It requires no modification to the
receiver. It simply replaces your rear push pin and drops right in.

M16/Ｍ４系用テンションピン


地味なパーツですが、結構探してる人は多く時々問い合わせがあるので紹介します。

締め込む事でアッパーとロアーのガタを減らすパーツだそうです。
私は使った事無いので効果は不明ですが購入して戴いたお客様より感謝されたので
それなり？の効果ある様です。

興味ある人はどうぞ・・・

在庫/価格のお問合せ/お求めはモデルショップPAPAまで
メール　hirokomama0527@yahoo.co.jp