2014年02月15日

LaRue Tactical 30mm 2 Piece QD LT123


放出品中古 LaRue Tactical 30mm 2 Piece QD LT123

Standard-height rifle scope rings with QD functionality.
The LT123 rings are ideal when mounting rifle scopes with extra large objective lenses, where clearance is a concern. These 30mm rings attach to any MIL-STD-1913 Picatinny rail, but are the perfect-match for the LT113 on Remington 700 model rifles.

The LT123 positions the centerline of the optic 1.28" above the top of the rail.

LaRue製 LT123の軍放出品中古です。

中古品ですが大きな傷や損傷も無く実用上は全く問題無いモノです。
レバー基部にマウント痕はありますが使用感も少なく軍放出中古としては
かなり良品だと思います。

当店通常新品価格 48000円程度(為替レートで変化あり) ⇒ 中古放出品特価 30000円


在庫/価格のお問合せ/お求めはモデルショップPAPAまで
メール hirokomama0527@yahoo.co.jp


14/2/18~2/24まで出張の為、出荷や連絡が滞る事がありますので
ご了承ください。


  

2014年02月15日

TROY TRX Alpha Rail, 7-1/4"


TRX Alpha Rail, 7-1/4"
Easy-To-Align Free-Float Handguards; Fixed Quad-Rail & User-Configurable Models


Machined aluminum free-float handguard employs a unique barrel nut and rotary-locking system
to ensure proper alignment of top rail with receiver rail. Handguard slides over barrel and gas tube
at an offset angle, until the notched barrel nut indexes in the internal grooved channel for a secure fit.
Two hex head screws lock down the handguard, and a built-in stop prevents over tightening.
Vent holes let heat escape the barrel and minimize weight. White alpha-numeric designators on
the cross-slots ensure easy repeatability of accessory positions. Streamlined Extreme and Alpha
models have a single, top Picatinny rail, deep horizontal grooves for a secure no-slip grip, and
additional ventilation holes to reduce weight and dissipate heat. Come with three bolt-on rails for
mounting additional accessories exactly where you need them. TRX-308 Extreme fits DPMS,
Remington, and Bushmaster AR-style .308 rifles. Alpha models fit standard factory AR-15/M16
barrel nut. 11 and 13 inch models available with built-in front sight post.


米国トロイ製 TRXレール 7-1/4インチ

TRX-ALPHAは旧型であるTRX-EXTと比較して専用バレルナットが不要となるので
一見楽そうですが実は一旦バレルナット外す必要があるのであまり着脱上のメリット
は見出せません。まぁ私の立場で見た話なのでお客様には関係ないかも?

しいて言えば専用レンチと専用バレルナットが要らなくなったぶん箱も含めた重量
がかなり軽くなった程度でしょうか? これもあまりどうでも良い話?

在庫/価格のお問合せ/お求めはモデルショップPAPAまで
メール hirokomama0527@yahoo.co.jp


14/2/18~2/24まで出張の為、出荷や連絡が滞る事がありますので
ご了承ください。

  

Posted by papa at 17:03Comments(0)実物パーツ・工具

2014年02月15日

余剰品セール Tenebraex Trijicon KillFlash w/ LIF


Tenebraex Trijicon ACOG KillFlash w/ LIF (Laser Interference Filter)


•Flip up Cap
•AGA-ARD Adapter
•Killflash w/ LIF Filter (Laser Filter Unit)
•NSN # 1240-01-540-2890

官給のACOG(TA31RCO等)に装着されるキルフラッシュキットです。
通常のキルフラッシュだけでは無くLIF内蔵なのでレーザー照射に対する
耐攻性もあります。
またフリップアップキャップも装備しておりますので使わない時は埃等の
ガードにもなります。

大人の事情でTrijiconのブリスターパックには入っていません。
理由はなんとなくご察し下さい。
レプリカではありません。偽物と判明すれば返品可能です。
もちろん商品代金は返金します。

現地価格 $139.99
国内参考価格 2~2.5万円

限定二個のみ 18800円(送料別) 

在庫/価格のお問合せ/お求めはモデルショップPAPAまで
メール hirokomama0527@yahoo.co.jp


14/2/18~2/24まで出張の為、出荷や連絡が滞る事がありますので
ご了承ください。

  

2014年02月15日

34mm Scope Ring Set (Pair)- US Combat Rated


34mm Scope Ring Set (Pair)- US Combat Rated

These rings are specifically designed to be used on any high end sniper, target or hunting
scopes with 34mm tubes.. Super Heavy Duty Steel construction for GREATER STABILITY!
Height / Rise: Single Sniper Heavy Duty Ring is available in a 1.100" / (28mm) rise.
This means that from the top of the rail / flat top / scope mount surface to the center of the
34mm diameter ring is 1.100" / (28mm). MFI hasthese rings on many oftheirtest weapons.
Just a super quality ring at a very reasonable price. MFI has been working with Premier
Reticles for the past year or so to develop a single ring that will meet a number of criteria.
Basically the more we manufacture for different applications the more cost effective they
become. The basic premise was to make a ring that fit the following criteria:

1.Width of the ring should be such that the thickness is adequate to be used for both front
and back positions on most scopes, thus eliminating the need for a wider ring in front.

2.Height of the ring should be the bare minimum that can be used with the Premier Reticles
3-15 power Tactical scope with a 50mm objective lense on a flat rail WITHOUT the lense
cover attached and still clear the rail near the objective lenses. As you can see from our
photos below where we use a PTR-91 and a 14" long MFI HK Low Profile Scope Mount,
that the front of the objective lense just clears the rail. The outer most ring of the scope
(used to provide a lip for the lens cap) fits down into the channel of the picatinny rail.

3.Height of the ring should be allow minimum clearance for a M14 / M1A when using a
ARMS M14 mount in conjunction with the PR 3-15 X 50mm Tactical scope WITH the lenses
cover attached and still clear the hand guard near the objective lense.

4.Height of the ring should be allow acceptable alignment to be used in conjunction with
standard PVS-22, PVS-24 and PVS 27 Night Vision scopes. So on a FLAT RAIL the scope
height for the 34mm should be within 40% of that of the standard height of the mount for the
night vision scope. Ours allows nearly 68% meaning little or no loss in resolution from being
off center.

5.Height of the ring should be allow acceptable clearance, yet still being as low profile as
possible to be used in conjunction with the SAKO TRG, Remington 700 or M24 Sniper
Variants with standard scope mounts and using the either a Premier Reticles 3-15 X 50mm
OBJ Tactical Scope or Premier Reticles 5-25 X 56mm OBJ Tactical Scope WITH the lenses
cover attached and still clear the hand guard and or barrel.

6.Rings include an insert to reduce the ring diameter to 30mm in order to sell these into
a double market.

7.Rings come with both Wrench Nut and Wing Nut / Tool-less style attachment points.

8.Rings made in the USA.

SPECIFICATIONS / SPECIAL FEATURES:
■100% Made In the USA.
■100% 1913 Mil. Spec. Picatinny.
■All Steel Construction High Pressure Casting then Precision Machined from 4140.
■Designed to withstand the recoil of a 50 caliber BMG round.
■Designed to mount on Standard Dovetail (Weaver) or Picatinny 1913 Style Rails.
■Held securely by 4 socket head cap screws using a standard allen / hex key (NOT Torques or Phillips) for removal.
■34mm Diameter but, also come with 30mm inserts (aluminum) for 30mm diameter optics.
■Overall Length / Thickness: @ 0.850 inch / 21.50 mm.
■Cross Over Lock Down Bolts are hardened Weapons Grade Steel.
■Super Knurled Wing Nut attachment for Fast & Easy ON and OFF.
■BOTH Wing Nuts and Standard Aim Point Style Locking Nuts are supplied at no added cost.
■Military Matt Black Finish (Black Oxide Coated Mil-C-13924 Standard).
■Medium Height Profile. (1.100 inch / 28mm rise) [ Top of your rail / mount to center of 34mm hole. ] or 0.435" / 11mm
[ Top of your rail / mount to bottom of the 340mm hole. ]
■Top of ring has slots cut for lighter weight.
■Weight @ 6.0 oz. (per ring with wing nut.)

34mmのスコープマウントは高価なモノが多いですが比較的リーズナブルな価格で
お求め出来るこのUS製マウントはお奨めです。

リングアダプターが付いており一般的な30mmでも使えますのでこの機会に2セット
購入しても損は無いと思います。


先着2名様に、HK製実物ステッカーをプレゼント中。
ステッカー品切れ時はご容赦下さい。

在庫/価格のお問合せ/お求めはモデルショップPAPAまで
メール hirokomama0527@yahoo.co.jp


14/2/18~2/24まで出張の為、出荷や連絡が滞る事がありますので
ご了承ください。